Tutorials

How to Create a Warm Sunset Effect in Lightroom 5


No Comments

Introduction

This is a Lightroom 5 tutorial, where I show you how to take an image with neutral blue tones and give it a warm sunset effect. The image that I will be working with today was taken during the afternoon while the sun was still fairly high and bright in the sky. This effect would work better on images that were taken later on in the afternoon where more warmer tones were available, but I wanted to give you an idea of the range of possibilities available in Lightroom while only using the sliders, especially when trying to get the most out of an otherwise unimpressive image.
 
I did not use any graduated filters or brush enhancements in this tutorial. All I did was play around with the sliders to achieve this look. This is a great tutorial for beginners who are still getting used to Lightroom and post-camera editing.
 

Here are the before and after shots:

I started off with the before image shown above, which was shot in RAW with a Canon EOS 60D and a focal length of 32mm, 100 ISO, f10 and an exposure time of 1/1000. I also added an exposure of +1.00 in Lightroom and did a bit of cropping.
The settings that I have used in this tutorial are just rough guidelines that worked well with this particular image. You will most likely need to tweak them when applying it to your own images, depending on what you’re working with.

 

Step 1: Basic Adjustments

 

 05cd7-screenshot2014-02-24at12-51-29am

 

To start off, I wanted to add a little bit of warmth to the image by increasing the temperature. I also increased the tint just a bit towards the magenta side to prevent the image from looking too green. This also adds more of the rich warmth effect that we are after.
 
9bc62-img_3945-1-4
 

Next, I increased the contrast to about +50 to add some depth to the image. I also increased the shadows and blacks while decreasing the highlights and whites to add even more depth.

 

66c43-screenshot2014-02-24at12-51-36am

 

77989-screenshot2014-02-24at12-51-42am
Finally, I decreased the clarity to give some softness to the overall image.
cdf53-screenshot2014-02-24at12-51-46am

And we end up with the following image below:

27888-img_3945-1-3

Step 2: Tone Curve

We can give a nice boost to the image by adding additional contrast through the use of an ‘S’ curve, which will deepen the shadows while brightening up the highlights.

4e13a-screenshot2014-02-24at12-51-52am

cb4c5-img_3945-1-2

 

Step 3: Sharpening & Noise Reduction

Since I did crop the image, I decided to add some sharpening to give it a crisper look.

0eb1c-screenshot2014-02-24at12-52-01am

Cropping an image, as well as sharpening and adding depth through shadows and highlights, is bound to give the image some noise, so it’s a good idea to incorporate some noise reduction to smooth things out.

89dff-screenshot2014-02-24at12-52-06am

Step 4: Vignetting

If you find that the brightness is not very even around the borders of the image, adding a lens vignette can definitely help even everything out. I did not incorporate a lens vignette in this image (simply because I didn’t feel like it), but I did incorporate a vignette effect.
I personally enjoy adding vignette effects to images because I just love the overall look of it. This is purely a personal choice that really depends on your own taste.
Here are the vignette levels that I added:
0fd91-screenshot2014-02-24at12-52-18am

And this gives me the final look:

17869-img_3945-1-6
And there you have it! I hope you found this helpful. I would love to hear your thoughts on this tutorial, so please feel free to leave comments/questions below! 🙂
Uncategorized

New Adventures!


No Comments

I have always dreamed of becoming an environmental photographer, but it seemed so far fetch to me that I never took it seriously until recently. And I am so glad I did take it seriously because I have been accepted into Environmental Visual Communication, a 7-month post-graduate program at Fleming College!! I hope this will allow me to really work on my skills as a photographer and give me the field experience that I need to get my career rolling. I am so grateful for this opportunity, and I am beyond excited to start this new adventure! Good things are coming! 🙂

P.S. I apologize for the inactivity recently. I’ve been extremely busy with school and just haven’t had the time to mess around with my photography. But I will post again soon! 🙂

Tutorials

DIY lightbox


1 Comment
Lighting is a very important aspect of photography, and can make the difference between a good shot and an excellent shot. However, for most of us that are just starting out, it can be quite expensive to invest in studio lighting, flash diffusers, etc.
Digital Photography School, one of my favourite photography blogs, has an amazing list of tutorials that show you how to create your own lighting equipment at home without spending a ton of money. You can check out the list here: http://digital-photography-school.com/diy-flash-and-lighting-hacks-for-digital-photographers
One thing I noticed in many commercial photographs is the crisp white backgrounds that appear behind objects. A great way to achieve this look is by using a lightbox that creates a soft light effect on the object from above and gives the image a crisp background.

 

I created my own versions of the lightbox today, one with a black background and one with white. The fabric I chose to use was white fleece, simply because I already had some lying around at home. But any type of fabric will work well. I wasn’t very picky with the box sizes, since it was just to try it out and see how it works. But after seeing the final results, I wish my white box was as big as the black box. I may end up creating another one that’s a bit bigger.

86767-img_4360

I also created my own lighting (with the help of my awesome dad). At first, I went looking for table lamps and desk lamps that I could use, but I was unsatisfied with everything I saw, so I ended up creating my own version of lighting that can be used to light up the lightbox, as well as be used for portraits and other shots. Here’s what my light looks like:

4d0b5-img_4363
DIY lightbox

As you can see, the cone is pretty tall. I tried different sizes, and this was what satisfied me the most in terms of how well it lit up the lightbox. Of course, the sizes will vary according to the light bulb you use and the size of your box.

To make the light, I took an old extension cord I had lying around at home, and cut off the end that had the sockets (don’t cut off the end with the plug!). Afterwards you need to pull out the wires from inside the outer rubber covering and attach it to a light bulb holder (my dad helped me with this part). Basically, you need to get one of those light bulb holders (I got mine at Home Depot for 3 bucks) and attach the wires on one end and the light bulb at the other end, and screw it all in place. It only took about 5 minutes to put everything together. I used a bright white light bulb, and a 12ft extension cord (this allows a bigger range of movement if I decide to use the light for portraits). For the cone, I used a piece of black bristol board, with white paper glued on the inside, and wrapped it around the holder and taped it in place.

Here are some samples of how my pictures turned out when taken inside the lightbox:

It’s super easy to make, super cheap, and works super well!! 🙂

 

If you decide to try it out for yourself, let me know how it turns out! 🙂